Replaces Approved Vendor PCS100New Aftermarket Outright

SYSTEM TOOL SENSOR, 28 MM DIA, 24 VDC, 250 MA, 120 MM

Your price:
$207.63 eachEstimated to ship by 12/24 if ordered before 4:30 PM EST
HomeApproved Vendorrpipcs100
SYSTEM TOOL SENSOR, 28 MM DIA, 24 VDC, 250 MA, 120 MM
SYSTEM TOOL SENSOR, 28 MM DIA, 24 VDC, 250 MA, 120 MM

Replaces Approved Vendor PCS100
SYSTEM TOOL SENSOR, 28 MM DIA, 24 VDC, 250 MA, 120 MM

New Aftermarket Outright
Your price:
$207.63 each
Ready to shipReady to Ship
Estimated to ship by 12/24 if ordered before 4:30 PM EST
Asset Information
ADD TO LIST
Product Overview

  • The pcs-100 is mechanically adjustable, which allows you to easily set or change the sensing needle sweep from 5° - 175° in either cw or ccw direction
  • We've also eliminated the need to use a miniature reversing gear box, subject to constant wear and tear
  • With a capability of over 80 cycles per minute, the pcs-100 will keep pace with your fastest machine
  • After mounting, set-up of the pcs-100 tool sensor is simple
  • Simply set the desired swing angle and swing direction for your application using the patented adjustment feature on the pcs-100 sensor
  • Make sure the tool or object to be checked is located between the start and end position of the swing angle selected
  • Now flick the selector switch on the scu-100 sensor control unit to correspond with the cw or ccw swing direction selected
  • If the sensing needle is allowed to travel to its end, indicating a broken tool (or missing object), a fault output is generated by the scu-100 sensor control unit, causing the machining to cycle stop or to be put in a feed hold
  • The scu-100 sensor control unit monitors the set-up of the pcs-100 system, and will indicate a system fault if you have incorrectly set swing direction or if electronic failures occur between the pcs-100 positive contact sensor and the scu-100 sensor control unit such as in the case of a cable disconnect or short
  • The design of the pcs-100 system is such that it does not fault if the sensing needle is held back from contacting the tool or object being monitored
  • It will only fault when the tool breaks or the object is missing
  • This can avoid expensive nuisance faults in many applications

    • Technical Specs
    P/N: PCS100 Key Specs
    Item
    SYSTEM TOOL SENSOR, 28 MM DIA, 24 VDC, 250 MA, 120 MM
    OEM
    Approved Vendor
    OEM #
    PCS100
    Condition
    New Aftermarket
    Returnable
    Yes
    Warranty
    As Is
    Diameter
    28 mm
    Power Requirements
    24 VDC, 250 MA
    Fitments

  • The pcs-100 is mechanically adjustable, which allows you to easily set or change the sensing needle sweep from 5° - 175° in either cw or ccw direction
  • We've also eliminated the need to use a miniature reversing gear box, subject to constant wear and tear
  • With a capability of over 80 cycles per minute, the pcs-100 will keep pace with your fastest machine
  • After mounting, set-up of the pcs-100 tool sensor is simple
  • Simply set the desired swing angle and swing direction for your application using the patented adjustment feature on the pcs-100 sensor
  • Make sure the tool or object to be checked is located between the start and end position of the swing angle selected
  • Now flick the selector switch on the scu-100 sensor control unit to correspond with the cw or ccw swing direction selected
  • If the sensing needle is allowed to travel to its end, indicating a broken tool (or missing object), a fault output is generated by the scu-100 sensor control unit, causing the machining to cycle stop or to be put in a feed hold
  • The scu-100 sensor control unit monitors the set-up of the pcs-100 system, and will indicate a system fault if you have incorrectly set swing direction or if electronic failures occur between the pcs-100 positive contact sensor and the scu-100 sensor control unit such as in the case of a cable disconnect or short
  • The design of the pcs-100 system is such that it does not fault if the sensing needle is held back from contacting the tool or object being monitored
  • It will only fault when the tool breaks or the object is missing
  • This can avoid expensive nuisance faults in many applications

      • Pelton & Crane
        • VALIDATOR 10
        • VALIDATOR 8
      Product Overview

    • The pcs-100 is mechanically adjustable, which allows you to easily set or change the sensing needle sweep from 5° - 175° in either cw or ccw direction
    • We've also eliminated the need to use a miniature reversing gear box, subject to constant wear and tear
    • With a capability of over 80 cycles per minute, the pcs-100 will keep pace with your fastest machine
    • After mounting, set-up of the pcs-100 tool sensor is simple
    • Simply set the desired swing angle and swing direction for your application using the patented adjustment feature on the pcs-100 sensor
    • Make sure the tool or object to be checked is located between the start and end position of the swing angle selected
    • Now flick the selector switch on the scu-100 sensor control unit to correspond with the cw or ccw swing direction selected
    • If the sensing needle is allowed to travel to its end, indicating a broken tool (or missing object), a fault output is generated by the scu-100 sensor control unit, causing the machining to cycle stop or to be put in a feed hold
    • The scu-100 sensor control unit monitors the set-up of the pcs-100 system, and will indicate a system fault if you have incorrectly set swing direction or if electronic failures occur between the pcs-100 positive contact sensor and the scu-100 sensor control unit such as in the case of a cable disconnect or short
    • The design of the pcs-100 system is such that it does not fault if the sensing needle is held back from contacting the tool or object being monitored
    • It will only fault when the tool breaks or the object is missing
    • This can avoid expensive nuisance faults in many applications

      • Technical Specs
      P/N: PCS100 Key Specs
      Item
      SYSTEM TOOL SENSOR, 28 MM DIA, 24 VDC, 250 MA, 120 MM
      OEM
      Approved Vendor
      OEM #
      PCS100
      Condition
      New Aftermarket
      Returnable
      Yes
      Warranty
      As Is
      Diameter
      28 mm
      Power Requirements
      24 VDC, 250 MA
      Fitments

    • The pcs-100 is mechanically adjustable, which allows you to easily set or change the sensing needle sweep from 5° - 175° in either cw or ccw direction
    • We've also eliminated the need to use a miniature reversing gear box, subject to constant wear and tear
    • With a capability of over 80 cycles per minute, the pcs-100 will keep pace with your fastest machine
    • After mounting, set-up of the pcs-100 tool sensor is simple
    • Simply set the desired swing angle and swing direction for your application using the patented adjustment feature on the pcs-100 sensor
    • Make sure the tool or object to be checked is located between the start and end position of the swing angle selected
    • Now flick the selector switch on the scu-100 sensor control unit to correspond with the cw or ccw swing direction selected
    • If the sensing needle is allowed to travel to its end, indicating a broken tool (or missing object), a fault output is generated by the scu-100 sensor control unit, causing the machining to cycle stop or to be put in a feed hold
    • The scu-100 sensor control unit monitors the set-up of the pcs-100 system, and will indicate a system fault if you have incorrectly set swing direction or if electronic failures occur between the pcs-100 positive contact sensor and the scu-100 sensor control unit such as in the case of a cable disconnect or short
    • The design of the pcs-100 system is such that it does not fault if the sensing needle is held back from contacting the tool or object being monitored
    • It will only fault when the tool breaks or the object is missing
    • This can avoid expensive nuisance faults in many applications

        • Pelton & Crane
          • VALIDATOR 10
          • VALIDATOR 8
        Product Overview

      • The pcs-100 is mechanically adjustable, which allows you to easily set or change the sensing needle sweep from 5° - 175° in either cw or ccw direction
      • We've also eliminated the need to use a miniature reversing gear box, subject to constant wear and tear
      • With a capability of over 80 cycles per minute, the pcs-100 will keep pace with your fastest machine
      • After mounting, set-up of the pcs-100 tool sensor is simple
      • Simply set the desired swing angle and swing direction for your application using the patented adjustment feature on the pcs-100 sensor
      • Make sure the tool or object to be checked is located between the start and end position of the swing angle selected
      • Now flick the selector switch on the scu-100 sensor control unit to correspond with the cw or ccw swing direction selected
      • If the sensing needle is allowed to travel to its end, indicating a broken tool (or missing object), a fault output is generated by the scu-100 sensor control unit, causing the machining to cycle stop or to be put in a feed hold
      • The scu-100 sensor control unit monitors the set-up of the pcs-100 system, and will indicate a system fault if you have incorrectly set swing direction or if electronic failures occur between the pcs-100 positive contact sensor and the scu-100 sensor control unit such as in the case of a cable disconnect or short
      • The design of the pcs-100 system is such that it does not fault if the sensing needle is held back from contacting the tool or object being monitored
      • It will only fault when the tool breaks or the object is missing
      • This can avoid expensive nuisance faults in many applications

        • Technical Specs
        P/N: PCS100 Key Specs
        Item
        SYSTEM TOOL SENSOR, 28 MM DIA, 24 VDC, 250 MA, 120 MM
        OEM
        Approved Vendor
        OEM #
        PCS100
        Condition
        New Aftermarket
        Returnable
        Yes
        Warranty
        As Is
        Diameter
        28 mm
        Power Requirements
        24 VDC, 250 MA
        Fitments

      • The pcs-100 is mechanically adjustable, which allows you to easily set or change the sensing needle sweep from 5° - 175° in either cw or ccw direction
      • We've also eliminated the need to use a miniature reversing gear box, subject to constant wear and tear
      • With a capability of over 80 cycles per minute, the pcs-100 will keep pace with your fastest machine
      • After mounting, set-up of the pcs-100 tool sensor is simple
      • Simply set the desired swing angle and swing direction for your application using the patented adjustment feature on the pcs-100 sensor
      • Make sure the tool or object to be checked is located between the start and end position of the swing angle selected
      • Now flick the selector switch on the scu-100 sensor control unit to correspond with the cw or ccw swing direction selected
      • If the sensing needle is allowed to travel to its end, indicating a broken tool (or missing object), a fault output is generated by the scu-100 sensor control unit, causing the machining to cycle stop or to be put in a feed hold
      • The scu-100 sensor control unit monitors the set-up of the pcs-100 system, and will indicate a system fault if you have incorrectly set swing direction or if electronic failures occur between the pcs-100 positive contact sensor and the scu-100 sensor control unit such as in the case of a cable disconnect or short
      • The design of the pcs-100 system is such that it does not fault if the sensing needle is held back from contacting the tool or object being monitored
      • It will only fault when the tool breaks or the object is missing
      • This can avoid expensive nuisance faults in many applications

          • Pelton & Crane
            • VALIDATOR 10
            • VALIDATOR 8